BOGNER SHIVA MANUAL PDF
Featuring two highly evolved channels, capable of clean tones that shimmer like icicles in the deep of winter moonlight and tube saturation that is so rich and. SHIVA MANUAL – Bogner . UBERSCHALL TWIN JET MANUAL – Bogner Bogner Alchemist User Manual – Revision C – Download BOGNER SHIVA SCH service manual & repair info for electronics experts.
|Published (Last):||7 April 2011|
|PDF File Size:||8.17 Mb|
|ePub File Size:||19.16 Mb|
|Price:||Free* [*Free Regsitration Required]|
This is the 80watt EL34 version.
Bogner shiva manual – grhzhsb’s soup
This was the only way to have a boost function on this channel with the original unboosted tone preserved. This means the Bass and Treble controls are not in the circuit anymore and have no effect on the sound. Next, flick the power switch front panel, right side to the center “standby” position and let the amp warm up for several minutes. If you hook up only one cabinet, the impedance ohm value of amp and cabinet should match: No ads displayed on the blog On reverb models, the reverb is always on if the reverb footswitch plug isn’t connected.
Repairs should be done only by knowledgeable Technicians!! Current Shivas have a 4-position rotary switch on the right-side back panel. The Bogner Shiva Head with Reverb tube guitar amplifier head packs a lot of punch into a very portable package that sounds great Shiva Series User Manual Oct 15, – Hi everybody, I have finally found a rig that I am really satisfied with.
To add a second speaker cabinet, use the second speaker jack and make sure both cabinets have matching impedances, the speaker output jacks are parallel so be sure to change the impedance selector to “half” the impedance rating of one speaker cabinet.
How to use it: That way you make sure it is the Amp.
Bogner shiva manual Bogner shiva manual Link: We let our amps run for at least bognre days before we ship them to make sure that the tubes work properly but since they have a glass housing and delicate little plates inside them it happened that they got damaged during shipping.
If you plug into the send you tap the signal of the Pre Amp and you could also send it to a recording device, mixer or another power amp etc. You can get those from Radio Shack.
The footswitch jacks are located on the back panel. Use only type “3AG Bogher Blow” fuses.
Mnual if you use the Loop the Channel Volume controls work like send levels, the higher you set the Volume, the more Level comes into the Effect. Be careful as this can add massive bottom to your sound which might overpower other frequencies and cover up an overall balanced sound.
Set the Master Manuual for overall Volume. If the Main fuse blows it could be just a voltage peak from your power outlet.
Read this owners manual completely before use to fully understand your Shivas functions. Don’t be the product, buy the product! The clean channel has an entire new boost circuit. Bkgner rotary switch is bognner active when the footswitch is not plugged in. The Loop circuit is always in the sound chain even if nothing is hooked up to it.
Troubleshooting Make sure your read and understand the safety instructions!! If you want to use an instrument level floor Effect unit or if your line level rack Effect unit is too sensitive for the hot send signal, you can use our special built in Boost Amp.
The “Power Amp In” bypasses the Shiva’s preamp, you can still use the Master volume and Presence controls since these controls are part of the power amp circuit. If you hook up two cabinets they must have the same impedance, same ohm value. If manuap still overloading the effects input, remember to lower the individual channel volume levels since they control how hot the effects loop send signal is, shva can then turn up the “Global Master Volume” to control your amps overall volume.
Shiva 6L6 models made before June approx. Reverb with independent reverb level controls for each channel. The Shift button will as it is labeled shift the EQ. Foot-switchable boost function for both channels, variable for channel 2. Featuring two highly evolved channels, capable of clean tones that shimmer like icicles in the deep of winter moonlight and tube saturation that is so rich and powerful it should be illegal in the free world.
Fuses To check the fuses, use an Ohmmeter to make sure they’re blown because sometimes you can’t see if they’re blown. To check the fuses, use an Ohmmeter to make sure they’re blown because sometimes you can’t see if they’re blown. When ready to play, flick the power switch up to the “play” position. As always, you must have the amp under load from a speaker cab or load box or damage may occur.
The EL 34 Model has one 16 and two 8 ohm speaker outputs the transformer has an internal 4 ohm tap also, so the outputs blgner be wired to 8 4 4 or 16 8 4 ohms if you wanted your amp customized. If you want to experiment with different tubes the whiva 3 tubes are the most noticeable ones, soundwise.
The gain channel features higher gain and a slightly more refined type of gain.
Your individual channel volume levels control how hot the effects loop send signal is, depending on the effect unit you may have to keep the channel volumes lower but you can then turn up the “Global Master Volume” to control your amps overall volume.
This is because the reverb circuit loads the amp down. NOTE using the “older version” Shiva without the footswitch connected: Bogner shiva and Acstacy Service Bogner shiva manual pdf.
The tone controls stay in the circuit and affect the sound.