CCNA 3 Final Exam Answers (v+v) – Scaling Networks 1. A network designer is considering whether to implement a swit. View Test Prep – -CCNA 3 Final Exam Answers vv60 Scaling Networks (1).pdf from S at Deakin. CCNA 3 Final Exam Answers CCNA 3 Final Exam V Answers only computer 4 CCNA 2 Final Exam V Answers computer 3 and RTR-A CCNA 1 Chapter 10 V Answers computer 4.

Author: Naramar Tejind
Country: Dominica
Language: English (Spanish)
Genre: Education
Published (Last): 9 August 2013
Pages: 175
PDF File Size: 15.80 Mb
ePub File Size: 20.23 Mb
ISBN: 541-7-46891-241-3
Downloads: 11920
Price: Free* [*Free Regsitration Required]
Uploader: Voodoolrajas

Documents Flashcards Grammar checker. Which security protocol or measure would provide the greatest protection for a wireless LAN? All trunk links are operational and all VLANs are allowed on all trunk links. An ARP request is sent by computer 5.

CCNA 3 Final Exam V4.0 Answers

Which device or devices will receive this message? Download Xeam Cisco Report Today! Introducing Routing and Switching in the Enterprise Version 4. Networking for Home and Small Businesses Version 4. Hosts A and B, connected to hub HB1, attempt to transmit a frame at the same time but a collision occurs.

Which hosts will receive the collision jamming signal? Router RA receives a packet with a source address of What will the router do with this packet? The router will drop the packet. Refer to the exhibit. Which two settings show the default value of VTP configuration on a Cisco switch? Which value determines if a switch becomes the central point of reference in the spanning tree topology? What is the purpose of the Spanning Tree algorithm?

It propagates VLAN configurations to other switches. It restricts broadcast packets to a single VLAN. It segments a network into multiple broadcast domains. It prevents loops in a switched network with redundant paths. What are two benefits of the IEEE Which configuration changes will increment the configuration revision number on the VTP server?

CCNA 3 v Exam Answers score %

A company has acquired a new office in a campus environment. Switches in the existing office and the new office are directly connected by a trunk link.

The computers in each office are not able to ping each other. What will fix the problem?

Use an access link between S2 and S3. Connect S2 and S3 to a common router. Configure the new office default gateway to What is a possible impact of setting too short an aging time in the MAC address table of a switch? Host A can communicate with host B, but cannot communicate with host C or host D. What is the cause of this problem? There is a native VLAN mismatch. The link between Switch1 and Switch2 is up but not trunked. Users complain that they do not have connectivity to the web server that is connected to SW1.

  ALU 74LS181 PDF

What should be done to remedy the problem? Allow all VLANs on the trunk link. Configure the trunk port in trunk mode on SW1. Attach the web server to a router and configure inter-VLAN routing. A new host needs to be connected to VLAN 1. Which IP address should be assigned to this new host? Using the command copy tftp: Why does the administrator not detect any changes in the switch configuration after the converted by Web2PDFConvert. The command should have been copy startup-config tftp: A backup configuration from a TFTP server cannot be copied directly into the startup-config.

The command copy running-config startup-config should be used to save the changes on the switch. Downloading to the startup-config requires the switch to be reloaded in order for the configuration to take effect. What two methods can be used to remove MAC address table entries from a switch? Power cycle the switch to clear all dynamically learned addresses. The clear switching-tables command will remove statically configured anawers.

The clear mac-address-table command will remove statically and dynamically configured table entries. The erase flash command will clear all statically configured table entries. Statically configured MAC addresses will automatically be removed from the address table minutes after the last exwm on a switch port.

Which type of traffic can exxm be received on a switch interface that is in STP blocking mode? BPDU frames multicast frames broadcast frames Layer 3 packets Which method establishes an administrative connection for configuring the Linksys WRTN wireless access point?

CCNA 3 v6.0 Exam Answers 2018 score 100%

Associate with the access point and then open a Fimal session with the access point. Physically connect to the access point and then reboot the computer to launch the configuration software. From a computer in the same IP subnet as the access point, enter the default IP address of the access point in a web browser. All edge ports are configured with the spanning-tree portfast command. The port will transition into blocking state. The port will transition immediately into forwarding state.

The fjnal will transition into blocking state and then immediately into forwarding state. The port will transition into blocking state and immediately transition through the listening and learning states.

What is true of the configuration of switch S1? The configuration steps that are listed in the exhibit have been entered in switch S1 via the console. Subsequent attempts to telnet to the switch are not successful. What is causing the problem? The switch must be configured with SSH version 1. The transport input command must specify Telnet access. The ip domain-name command must also be entered in line configuration mode for the vty lines. Which switch will be elected as the root bridge of the spanning tree topology?


If HostA sends a broadcast frame to SW1, which devices will receive the frame? Which two statements are true about the operation of the interfaces? Subinterfaces use unique MAC addresses by adding the Traffic inbound on this router is processed by different subinterfaces, depending on the VLAN from which the traffic originated.

The network administrator wants to configure a switch to pass VLAN update information to other switches in the domain but not update its own local VLAN database. Which two steps should the administrator perform to achieve this?

CCNA 3 Final Exam V Answers

Reset the VTP counters. Configure VTP version 1 on the switch. Configure the VTP mode of the switch to transparent.

Verify that the switch has a higher configuration revision number. Configure the switch with the same VTP domain name as other switches in the network. However, hosts B and D cannot ping each other. What is the most likely cause of this problem? The link between the switches is up but not trunked. Hosts B and D are configured with IP addresses from different subnets. Users A and B are reporting intermittent connectivity problems. Pre-installation surveys showed strong signal strength from the AP sxam to the client locations.

Outside electrical interference has been eliminated. Relocate the APs closer to each other. Increase the distance between the clients. Change the channel on AP-B to 6 or Why is it advisable that a network administrator use SSH instead of Telnet when managing switches? SSH encrypts only the username fnial password when logging in. SSH encrypts all remote management communications whereas Telnet does not. SSH sends a clear text message steam which reduces the bandwidth use for management. A student has decided to share access to the Internet by attaching a hub and laptop to STW as shown.