ENDA ETC 4420 PDF

0

Enda ETC PID Temperature controller Pt, J, K, T, S, R 2 A relay, SSR (L x W x H) 94 x 48 x 48 mm – now buy online with ease from Thank you for choosing ENDA ETC SERIES temperature controllers. Enter PID .. ETC ETC ETC ETC Pt 9. Pt 8. TC. TC. ET Double set point. Selectable sensor type (Pt, J, K, L, T, S, R). PID control function with accurate self-tuning. Digital inputs can be assigned to 3.

Author: Golkree Tarr
Country: Timor Leste
Language: English (Spanish)
Genre: Technology
Published (Last): 2 August 2004
Pages: 434
PDF File Size: 15.30 Mb
ePub File Size: 9.86 Mb
ISBN: 555-1-77603-222-6
Downloads: 81691
Price: Free* [*Free Regsitration Required]
Uploader: Fautaxe

ENDA ETC : Datasheet

Read this document carefully before using this device. The guarantee will be expired by damaging of the device if you don’t attend to the directions in the user manual.

Also we don’t accept any compensations for personal injury, material damage or capital disadvantages. Enter PID parameters of the system if they are known at the beginning. Otherwise, Self-Tune should be activated.

According to EN Front panel: IP65 Rated pollution degree Rear panel: Selectable as Control or Alarm2 output. Selectable logic control output. Max 12V 20mA Mechanical While cleaning the device, solvents thinner, benzine, acid etc. If this parameter is set to 0, the output power becomes 0 at the set point. Using this parameter the energy requirements of 44200 system is adjusted at the set point. So the set point can be achieved by minimum fluctuations and in the shortest time.

If this parameter is adjusted to a value closer to the energy requirements of the system at the set point, process temperature is prevented to rise or drop to dangerous levels. Adjustable between 0 and minutes. If 0 is selected, soft start feature will be enable and the device reaches set point value quickly. Four kinds of functions can be selected. The minimum value is the value of C.

  COSHIP N8102 PDF

The maximum value is endx value of C. The maximum value 44420 the value of A1. The maximum value is the value of A2. Filter for display value. Adjustable between 1 and If this parameter is 1, digital filter runs most quick.

If the parameter is 31, the filter run most slow. The value of parameter should be increased in interference. Adjusable between 1 and Difference addresses should be selected for every device.

If the temperature unit is changed, the value of the UPL.

IfInp parameter is selected TC or Pt, this parameter is seen. It should be Offset value is added to the measurement value.

The normal value is 0. If the selected input type is changed, the value of C.

If independent or deviation alarm is C. If no key is pressed within 20 seconds during programming mode, the data is stored automatically ebda the run mode is entered. SET Alternatively, the same function occurs first pressing key and then pressing keys together. After PID is calculated 25 P.

Press any key to deactivate the self-tune procedure. SET key, run message flashes. If process value is Appropriate to begin self tune, rEdY. Then press any key to see Pid.

Before self tune procedure, A. If self tune is achieved A. Before self tune procedure, temperature setpoint value should be adjusted.

When self tune procedure begins with no failure, Pid. When PID parameters are calculated, P. Then the device heats until setpoint value according to PID parameters and calculates the energy requirement for stable temperature and writes P.

If any key is pressed while Pid. If any key is pressed while P. If waited enough,the value increases at each step. After 1 second following the release of the key, initial condition is returned. The same procedure is valid for the decrement key. Data value during programming SV 3 Increment key during normal operation and programming Parameter selection key during programming 4 Decrement key during normal operation SET CSET If only this key is pressed in normal operation, software version number is seen.

  EVEN THE STARS LOOK LONESOME MAYA ANGELOU PDF

Set appears on the display. Then, the value is adjusted by using First, press and hold keys. Then, the value is adjusted by using If C. S different from out1. Alarm1 and Alarm2 setpoint values can be adjusted in sequence when per press keys. The maximum of C. SEt is the value of C. If independent alarm is selected, A1. If deviation alarm is selected, A1.

Enda ETC4420-230 ETC4420 PID Temperature Controller ETC4420-230 Data Sheet

If band alarm is selected, A1. Make sure that the device is used only for intended purpose. The shielding must be grounded on the instrument side. During an installation, all of the cables that are connected to the device must be free of energy. The device must be protected against inadmissible humidity, vibrations, severe soiling and make sure that the operation temperature is not exceeded.

All input and output lines that are not connected to the supply network must be laid out as shielded and twisted cables. These cables should not be close to the power cables or components.

What’s missing? Tell us about it.

The installation and electrical connections must be carried on by a qualified staff and must be according to the relevant locally applicable regulations. Therefore, when using a grounding thermocouple, do not connect the logic output terminals to the ground. Use suitable compensation cables. Don’t use jointed cables. Pay attention to the polarities of the thermocouple cables as shown in the figure right are connected to the.

When 2 wired Pt is used, terminals 6 and 7 must be short circuited. RS Modbus communication None It’s a endda project which helps to repair anything.