ISO 6621-5 PDF
ISO INTERNATIONAL. STANDARD. ISO. Second edition. Internal combustion engines — Piston rings —. Part 5. ISO. Second edition. Internal combustion engines — Piston rings —. Part 5: Quality requirements. Moteurs à combustion interne. STANDARD. ISO. Third edition. Reference number. ISO (E). This is a free 5 page sample. Access the full version online.
|Published (Last):||6 August 2013|
|PDF File Size:||1.9 Mb|
|ePub File Size:||7.10 Mb|
|Price:||Free* [*Free Regsitration Required]|
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. This does not preclude the free use, in course of imple- menting the standard, of necessary details, such as symbols and sizes, type or grade designations. Attention is particularly 66215 to the following: Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing.
This Indian Standard has been developed from Doc No.: Due to its wedge shape, any radial movement of the ring will alter its axial clearance and thus minimize the build-up of combustion residues.
ISO Internal combustion engines — Piston rings —Part 1: Vocabulary – MBA智库文档
In accordance with Adobe’s licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. For undated references, the latest edition of the referenced document including any amendments applies.
Due to its wedge shape, any radial movement of the ring will alter its axial clearance and thus minimize the build-up of combustion residues. Sio 9 Terms and definitions’. Unless otherwise isso, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from isk ISO at the address below or ISO’s member body in the country of the requester.
These terms designate either types of piston rings or certain characteristics and phenomena of piston rings. They may also be used for piston rings of compressors working under analogous conditions. They may isl be used for piston rings of compressors working under analogous conditions. Combinations of configurations listed in Tables 2 to 5 along with those in Table 1 are shown as “common features” in the relevant ISO Standard referenced in each table. The terms and definitions in this part of ISO apply to piston rings ios reciprocating internal combustion engines.
Cranes — Safety — Design — Requirements for equipment — Part 1: Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
The corresponding Indian Standard which is to be substituted in its place is given below along with its degree of equivalence for the edition indicated: Key 1 outside chamfered edge 2 peripheral edge 3 side face edge 4 inside chamfered edge Figure 5 — Chamfered edges 5.
Adobe is a trademark of Adobe Systems Incorporated.
Search the history of over billion web pages on 621-5 Internet. Coil-spring-loaded oil control rings of narrow width made of cast iron  ISOInternal combustion engines — Piston rings — Part 3: Users of Indian Standards should ascertain that they are in possession of the latest amendments or edition by referring to the latest issue of ‘BIS Catalogue’ and ‘Standards: For dated references, only the edition cited applies.
For undated references, the latest edition of 66621-5 referenced document 6612-5 any amendments applies. With the publication of this standard IS Part 9 shall be treated as withdrawn. However, only the terms given in the official languages can be considered as ISO terms. No part izo these publications may be reproduced in any form without the prior permission in writing of BIS. Piston ring nitrided on specific surfaces only e. The work kso preparing International Standards is normally carried out through ISO technical committees.
In this adopted standard, reference appear to the following International Standard for which Indian Standard also exists. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. These terms designate either types of piston rings or certain characteristics and phenomena of piston rings. This second edition cancels and replaces the first edition ISO ISO consists of the following parts, under the general title Internal combustion engines — Piston rings: The main task of technical committees is to prepare International Standards.
Certain conventions are, however, not identical to those used in Indian Standards. ISO shall not be held responsible for identifying any or all such patent rights. Basis of limits and fits: Pin point or burry light 6.
Pin point or burry light 6.