LM3911N DATASHEET PDF
LMN datasheet, LMN circuit, LMN data sheet: NSC – LM Temperature Controller,alldatasheet, datasheet, Datasheet search site for. Order Number LMN. See NS Package N08E. TO Package. TL H –7. Order Number LMH See NS Package H04A. 7. lmn – Download as PDF File .pdf), Text File .txt) or read online.
|Published (Last):||25 July 2018|
|PDF File Size:||6.80 Mb|
|ePub File Size:||4.54 Mb|
|Price:||Free* [*Free Regsitration Required]|
Fabricated on a single monolithic chip, it includes a temperature sensor, a stable voltage reference and an operational amplifier.
NATIONAL SEMICONDUCTOR LMN Temperature Control IC DIP8 OM – £ | PicClick UK
Using the internal op amp with external resistors any temperature datasheeet factor is easily obtained. By connecting the op amp as a comparator, the output will switch as the temperature transverses the set-point making the device useful as an on-off temperature controller.
An active shunt regulator is connected across the power leads of the LM to provide a stable 6. This allows the use of any power supply voltage with suitable external resistors.
The input bias current is low and relatively constant with temperature, ensuring high accuracy when high source impedance is used. Further, the output collector can vatasheet returned to a voltage higher than 6. The LM uses the difference in emitter-base voltage of transistors operating at different current densities as the basic temperature sensitive element. Since this output depends only on transistor matching the same reliability and stability as present op amps can be expected.
In the epoxy package all electrical connections are made on one side of the device allowing the other 4 leads to be used for attaching the LM to the temperature souce. Either Vb or V a can be ground. The output voltage applies to the basic thermometer configuration with the output and input terminals shorted and a load resistance of t 1. This is the feedback sense voltage and includes errors in both the sensor and op dayasheet. This voltage is specified for the sensor in a rapidly stirred oil bath.
The output is referred to V a.
The output leakage current is specified with t mV overdrive. Since datwsheet voltage changes with temperature, the voltage drive for turn-off changes and is defined as VOUT with output datasehet input shorted b mV. Application Hints media will conduct the heat from the sensor. Also, there are many small heat sinks designed for transistors which will improve heat transfer to the sensor from datasueet surrounding medium.
A small finned clip-on heat sink is quite effective in free-air. It should be mentioned that the LM die is on the base of the package and therefore coupling to the base is preferable. The internal reference regulator provides a temperature stable voltage for offsetting the output or satasheet a comparison point in temperature controllers. However, since this reference is at the same temperature as the sensor temperature, changes will also cause reference drift.
For application where maximum accuracy is needed an external reference should be used. Of course, for fixed temperature controllers the internal reference is adequate. Although the LM is designed to be totally trouble-free, certain precautions should be taken to insure the best possible performance.
Nominal suggested operating current for the shunt regulator is 1. In free, still, air this raises the package temperature by about 1. Although the regulator will operate at higher reverse currents and the output will drive loads up to 5. Therefore, the sensor should be operated at the lowest possible power level.
LM3911N PDF Datasheet浏览和下载
SCR heating, by proper positioning, can preheat the sensor giving control anticipation as is presently used in many home thermostats. Wire wound resistors will provide maximum temperature stability. Life support devices or systems are devices or systems which, a are intended for surgical implant into the body, or b support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user.
A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.
National Semiconductor Europe Fax: Tsimshatsui, Kowloon Hong Kong Tel: